# Lockout/Tagout Steps for Tools and Equipment

A practical walkthrough of lockout/tagout steps for tools and equipment: isolate energy, apply locks and tags, release stored energy and verify zero state.

Lockout/tagout is a set of steps that isolates hazardous energy from a tool or machine before anyone services it. The lockout/tagout procedure moves from notification and shutdown through isolation, lock and tag application, release of stored energy and verification of a zero energy state. Written as an energy control procedure, it keeps every person who works on the equipment protected by their own lock. 

- Shut the equipment down by its normal controls first, then isolate every energy source with a lock and a tag.
- Release stored energy in springs, capacitors, gravity loads and pressure lines before you touch the equipment.
- Verify the zero energy state by trying the start control and checking for residual energy.
- Every worker who services the equipment applies a personal lock in a group lockout.
- An out-of-service tag records who applied it and why, and it never replaces a lock.
 

## What lockout/tagout is for 

Lockout/tagout, often shortened to LOTO, is a planned sequence that controls hazardous energy while a tool or machine is serviced. Hazardous energy includes electricity, pressure, steam, gravity, springs and anything else that can start the equipment or release a stored force. The point of the sequence is to stop a machine from starting or releasing energy while a person is in reach of its moving parts. 

Lockout means placing a physical lock on an energy isolating device, such as a breaker, valve or plug lockout. Tagout means attaching a warning tag that names the person who applied it and the reason the equipment is out of service. A padlock and tag work as a pair, because the tag carries the information and the lock carries the physical hold. 

The rules behind this practice come from workplace safety standards such as OSHA 1910.147, which addresses the control of hazardous energy. Your own energy control procedure should list each machine, its energy sources and the exact isolation points. A written procedure turns a general safety idea into repeatable steps for your tools and equipment. 

## Step one: prepare and notify 

Preparation starts with knowing the equipment before you shut it down. Read the energy control procedure for that machine and identify every energy source, including lines that feed it from another area. Tell affected workers that the equipment is going out of service, because someone may rely on it or need to stop feeding it. 

Gather the hardware you need before you begin, such as padlocks, tags, lockout hasps and valve lockouts. Each lock should belong to one person, and each tag should be filled in with a name and a reason. Planning the sequence first prevents a worker from isolating one source and missing another. 

Only trained workers should perform the shutdown and isolation steps, and the training should match the equipment. A person who has not been trained on the procedure can expose others to a hazardous energy release. Where the equipment is complex or tied to a plant system, a qualified maintenance specialist should carry out the isolation. 

## Step two: shut down and isolate 

The shutdown step uses the normal operating controls to stop the equipment in an orderly way. Follow the manufacturer sequence so the machine comes to rest without stress on its parts or product inside it. A controlled shutdown is different from cutting power, because an abrupt stop can leave stored energy in the system. 

Energy isolation comes next, and it means operating every disconnect, breaker, valve or switch that feeds the equipment. Each isolating device is then secured in the off or closed position with a lock. A lockout device should hold the switch or valve itself, not just a nearby panel door. 

Every energy source gets its own lock, so a machine with electrical, pneumatic and hydraulic feeds needs three isolation points secured. Skipping one source leaves a path for the equipment to move or pressurize again. The lockout tagout steps only work when the isolation covers the whole machine instead of one feed. 

## Step three: release stored energy 

Stored energy is the force left in a machine after the supply is cut, and it must be released before work starts. Springs under tension, raised parts held by gravity, capacitors and pressurized lines all hold energy that can hurt a person. The energy control procedure should name the release method for each of these items on that machine. 

Release methods include bleeding pressure lines, blocking or lowering raised components and discharging capacitors with the proper tool. Grounding and blocking give a physical barrier that holds the part in place while hands are inside the machine. A block used for support should be rated for the load and placed so it cannot slip. 

Never rely on a valve position or a control reading alone as proof that energy is gone. A gauge can fail and a valve can leak past its seat, so the release step needs a physical check. Releasing stored energy is part of the lockout tagout procedure and not an optional extra. 

## Step four: verify the zero energy state 

Verification of zero energy state is the check that proves the equipment cannot start or move. The person performing the work tries the normal start control after isolation, with the machine clear of people and tools. A machine that stays still confirms the isolation held, and the control is then returned to the off position. 

Verification also covers the stored energy points, because a gauge at zero or a lowered part needs a direct check. Test instruments should be checked against a known live source before and after the reading where the procedure requires it. A verified zero state is the moment when service work can begin safely. 

Repeat the verification if the work pauses and the equipment is left for a later shift. Conditions can change while a machine sits idle, and a returning worker should treat it as unverified until checked. Documenting the check gives the next person a clear record of what was done. 

## Group lockout and shift changes 

Group lockout is used when several workers service the same equipment at the same time. Each worker applies a personal lock to a group lockout hasp or box, so the equipment cannot be re-energized until the last lock is removed. One lock held by a supervisor does not protect the people doing the work. 

Shift changes need a clear handover of locks and tags, because the person leaving may not be the person who finishes. A lock should stay in place until the worker who applied it removes it, or until the procedure defines a safe removal process. Removing another person lock without that process defeats the entire protection. 

A lock left behind after a job is finished should be handled by the written removal procedure, not cut off in haste. The procedure should confirm that the equipment is clear, the owner is contacted and the removal is recorded. Good lockout tagout safety depends on this discipline as much as on the hardware. 

## Tags, out-of-service marks and quarantine 

An out-of-service tag tells anyone who approaches the equipment that it must not be started or used. The tag carries the name of the person who applied it, the date and the reason for the shutdown. A tag is a warning device, and it does not physically prevent a switch from being closed. 

For that reason, a tag should be paired with a lock wherever the equipment can be locked out. Where a device cannot be locked, the procedure should describe extra measures such as removing a fuse or blocking a control. A padlock and tag together give both the physical hold and the written warning. 

Quarantine goes further and separates a tool from the workflow until it is repaired or inspected. A damaged tool or a machine awaiting parts can sit in a marked area with its tag visible to everyone. This keeps an unsafe item from being picked up and used while the repair is pending. 

## Lockout/tagout safety tips for a shop 

Lockout tagout safety rests on the hardware being ready and the procedure being followed the same way each time. Keep locks, tags, hasps and valve devices in one labeled station so a worker can reach them before starting a job. A missing lock is a reason to stop the job, not a reason to borrow one. 

Train every worker on the energy control procedure for the equipment they touch, and refresh that training when a machine changes. Review the procedure after a near miss or an unexpected startup, because the review shows where a step was unclear. Keep a written record of who is authorized to perform lockout on each machine. 

Inspect locks, tags and blocking devices before each use, and replace any item with damage or illegible writing. Only the worker who applied a lock should remove it, unless the written removal procedure is followed. A short pre-job check of the isolation points is the habit that keeps the sequence reliable. 

## Lockout/Tagout Questions for Tools and Equipment 

### What steps do you take to lockout/tagout a piece of equipment? 

The sequence is to notify affected workers, shut the equipment down by its normal controls, isolate every energy source, apply a lock and tag to each isolating device, release stored energy and verify the zero energy state. Only after verification does service work begin. The written energy control procedure for that machine defines the exact isolation points and release methods. 

### Does lockout/tagout apply to hand tools and small equipment? 

Lockout/tagout applies to any tool or equipment that can release hazardous energy while it is serviced. A corded or battery tool needs its plug or battery removed and controlled before service, and a bench machine needs its supply isolated. An out-of-service tag on a damaged tool keeps it out of the workflow until repair. 

### Can a tag replace a lock in a lockout/tagout procedure? 

No, a tag alone does not prevent a switch from being closed, so it should be paired with a lock wherever the equipment can be locked out. Where a device cannot be locked, the procedure should describe extra measures such as removing a fuse or blocking a control. The tag carries the warning and the name, while the lock carries the physical hold. 

### What is a group lockout and when is it used? 

A group lockout is used when more than one worker services the same equipment at the same time. Each worker applies a personal lock to a group hasp or lockout box, and the equipment stays isolated until the last lock is removed. This arrangement means no single person can re-energize the machine while someone else is still working. 

### Why is verification of zero energy state required? 

Verification of zero energy state proves that the isolation held and that no stored energy remains in the equipment. The worker tries the normal start control and checks the stored energy points before beginning service. A machine that stays still and shows no residual force is the condition that allows safe work to start. 

### What should a lockout tagout safety program include? 

A lockout tagout safety program should include a written energy control procedure for each machine, training for authorized workers and a supply of locks, tags and isolation devices. It should also cover group lockout, shift handover, tag removal and periodic review after an incident. The program is only as strong as the habit of following it on every job.
