# Lithium Battery Amp Hour Calculator

Learn how to calculate lithium battery amp hours from watt hours and voltage, adjust for usable capacity, and estimate cordless tool runtime for detailing.

A lithium battery amp hour calculator divides watt hours by nominal voltage to find amp hours. To estimate runtime, multiply that result by the usable share of capacity, then divide by tool current. The same arithmetic applies to a polisher pack, a cordless vacuum battery or a portable power station. 

- Amp hours equal watt hours divided by nominal voltage.
- Use nominal voltage, not the full-charge or 'max' voltage, in every calculation.
- Usable capacity equals rated capacity multiplied by your depth of discharge.
- Runtime in hours equals usable amp hours divided by average tool current.
- Compare packs with different voltages by watt hours, not amp hours.
 

## What an amp hour rating actually measures 

An amp hour rating measures how much electric charge a lithium battery can deliver over time. One amp hour means the pack can supply one amp of current for one hour. In theory, a 5 Ah pack supplies five amps for an hour or one amp for five hours. Lithium-ion battery capacity on a tool pack appears in amp hours (Ah) or milliamp hours (mAh). 

Amp hours alone do not tell you how much energy a battery stores. Stored energy combines charge with voltage and is measured in watt hours (Wh). A 2 Ah pack at 36 volts stores twice the energy of one at 18 volts. That gap explains why packs on different voltage platforms cannot be compared by amp hours alone. 

An amp hour figure becomes useful for planning once you link it to voltage and tool current. With those two numbers, you can estimate stored energy, usable capacity and runtime. Each result comes from simple multiplication or division, with no special software required. 

## The formula for Wh to Ah conversion 

Wh to Ah conversion uses one formula: amp hours equal watt hours divided by nominal voltage. A pack rated at 90 Wh and 18 volts nominal holds 5 Ah. At 36 volts, a 72 Wh pack works out to 2 Ah. 

The reverse conversion gives watt hours from amp hours: multiply Ah by nominal voltage. A 6 Ah pack at 18 volts stores 108 Wh of energy. Power stations and other large lithium batteries often list Wh instead of Ah. 

Milliamp hours convert to amp hours by dividing by one thousand. A cell marked 3000 mAh therefore holds 3 Ah. Convert every value to the same units before dividing, or the answer will be wrong. 

## Why nominal voltage belongs in the calculation 

Nominal voltage is the average working voltage of a battery as it discharges. That value, not the peak, belongs in every capacity calculation. A lithium-ion cell has a nominal voltage of about 3.6 to 3.7 volts. Fully charged, the same cell reads close to 4.2 volts. 

Tool packs connect cells in series, so pack voltage is cell voltage times the number of cells. Five cells in series give about 18 volts nominal and about 21 volts at full charge. Some brands print the full-charge figure on the pack as a 'max' voltage. For amp hour math, use the nominal figure from the label or the manual. 

Lithium iron phosphate (LiFePO4) batteries use a lower cell voltage of about 3.2 volts nominal. Some portable power stations used for mobile work rely on this chemistry. Check the chemistry before you pick a voltage, because the wrong cell value skews every result. 
| Cells in series | Nominal voltage (Li-ion) | Full-charge voltage | 
| 3 | about 10.8 V | about 12.6 V | 
| 5 | about 18 V | about 21 V | 
| 10 | about 36 V | about 42 V |  

## Usable capacity and depth of discharge 

Usable capacity is the share of rated capacity you can draw before the battery stops supplying power. Depth of discharge (DoD) describes how far a battery is emptied relative to its full rating. A pack run from full charge to its cutoff has used its full designed depth of discharge. 

Cordless tool packs contain a battery management system (BMS) that cuts power before cells drain too far. With that cutoff in place, a tool pack's rated Ah roughly matches what you can draw. Larger lithium systems, such as power stations, may list usable capacity apart from total capacity. In that case, run the calculation with the usable figure. 

To find usable amp hours yourself, multiply rated Ah by the depth of discharge as a decimal. A battery you stop at half charge delivers half its rated amp hours. Stopping before the cutoff costs runtime per charge but can reduce wear on the cells. 

## Turning amp hours into tool runtime 

Tool runtime in hours equals usable amp hours divided by the average current the tool draws. A 5 Ah pack feeding a steady 10 amp load gives a theoretical half hour. Halve the current and the same pack runs twice as long in theory. Multiply the hours by sixty to read the answer in minutes. 

Tool current can be estimated from watts by dividing power by the pack's nominal voltage. A tool drawing 180 watts on an 18 volt pack pulls 10 amps. Power figures printed on tools often describe maximum input, not the average draw during work. 

A shortcut skips amps entirely: runtime in hours equals usable watt hours divided by average tool watts. A 90 Wh pack powering a tool that averages 180 watts gives about half an hour. The watt hour method skips the voltage step, which removes one source of error. 

## Step-by-step amp hour calculation for a tool pack 

An amp hour calculation for a tool pack starts with the numbers on the battery label. Look for the nominal voltage plus a rating in Ah, mAh or Wh. If the label shows only a 'max' voltage, check the manual for the nominal value. 

Converting the label figures comes next, so every value shares the same units. Turn mAh into Ah, or divide Wh by nominal voltage to reach Ah. Then decide whether the full rating counts as usable or whether you stop earlier. 

The last step divides usable amp hours by the tool's average current to estimate runtime. Write the result next to each tool on your job checklist. Rerun the numbers whenever you switch to a different pack or tool. 

- Read nominal voltage and capacity from the pack label
- Convert mAh to Ah by dividing by 1000
- Or divide Wh by nominal voltage to get Ah
- Multiply Ah by your depth of discharge as a decimal
- Estimate tool current as watts divided by nominal voltage
- Divide usable Ah by tool current for runtime in hours
 

## Why real runtime differs from the estimate 

Real runtime on a cordless tool differs from the calculated figure because tool load changes during work. A polisher pressed hard on a panel draws more current than one gliding at low speed. Vacuums and blowers on high settings pull more amps than on low. Use a realistic average draw, not the lightest or heaviest moment. 

Battery temperature changes how much capacity a lithium pack delivers during a job. Cold cells give up less of their rated charge, while hot packs may trigger a protective shutdown. Heavy current draw causes voltage sag, a temporary drop in voltage under load. Strong sag can reach the cutoff point before the cells are actually empty. 

Battery age lowers capacity as lithium cells go through repeated charge cycles. An older pack may show the same label but deliver fewer amp hours than when new. Swollen, cracked or overheating packs are a fire risk and should be taken out of service. Do not open or rewire tool packs, and leave any cell repair to a trained battery specialist. 

## Comparing packs and planning batteries for a job 

Choosing between battery packs on one platform means weighing amp hours against weight and size. A higher Ah pack stores more energy but adds bulk to the tool. A lighter pack can suit a polisher held overhead on roofs or tall vehicles. A larger pack can suit a vacuum or blower that runs for long stretches. 

Planning batteries for a detailing job starts with the runtime estimate for each cordless tool. Add up the expected working time per tool, then compare it with runtime per pack. The comparison shows how many charged packs, or how much charging time, the job needs. 

A simple battery checklist keeps your packs in order between detailing jobs. Label each pack with its voltage, Ah rating and calculated runtime on your main tools. Charge every pack you plan to use before loading the work vehicle. Store lithium packs in a cool, dry place away from direct sun. 

## Lithium battery amp hour questions 

### How many amp hours do I need for a detailing job? 

The amp hours you need depend on each tool's average current and run time. Multiply average amps by working hours to find the Ah a tool requires. Spread that total across your packs, with a margin for cold weather and older batteries. 

### Why does a 20V max battery count as 18 volts? 

A 20V max pack works out as 18 volts because 20 volts describes it near full charge. Five lithium-ion cells in series average about 18 volts across a discharge. Capacity math uses that nominal value to give accurate amp hours. 

### Does a higher amp hour battery run a tool longer? 

Yes, a higher amp hour battery at the same voltage runs a tool longer under equal load. Doubling the Ah rating at equal voltage doubles the stored energy. The larger pack also adds weight and size to the tool. 

### Can I use a higher Ah battery in my cordless tool? 

Yes, a higher Ah pack can be used when the tool maker lists it as compatible. The pack's voltage and battery platform must match what the tool is designed for. Do not force a pack from another platform or rely on unapproved adapters. Mismatched packs can damage the tool or create a fire risk. 

### Is a calculated battery runtime exact? 

No, a calculated battery runtime is an estimate based on an average current draw. Load, temperature and battery age all move real runtime up or down. Treat the figure as a planning guide and keep a spare charged pack on hand.
