# How to Make Garage Cabinet Doors From Plywood

A plain guide to building plywood doors for a garage cabinet: measuring the opening, cutting panels, framing, fitting hinges and finishing the edges.

You make garage cabinet doors from plywood by cutting a panel to fit the opening, adding a frame or stiffener so the panel stays flat, and hanging it on hinges set for the door thickness. Accurate door sizing and a clean edge finish decide how the door looks and how well it closes. The work needs a flat surface, sharp blades and a steady hand with a saw. 

- Measure the cabinet opening first, then subtract the clearance the hinge needs to set the door size.
- A plywood panel alone can bow over a wide span, so add a frame or stiffener to hold it flat.
- Seal every cut edge, because exposed plywood edges soak up moisture and fray with handling.
- Match hinge type to door thickness and overlay before you drill any screw holes.
- Cut one test door and hang it before you repeat the process for the rest of the cabinet.
 

## Measure the opening before you cut 

Door sizing for a garage cabinet starts with the clear opening of the carcass, not with the old door. Measure the width and height at the top, middle and bottom of the opening and use the smallest figure. Garage floors and walls are rarely level, so a cabinet box can be slightly out of square. Write the numbers down and check them twice before you touch a saw. 

Decide how the door will sit against the cabinet before you set its size. A full overlay door covers the face frame, an inset door sits inside the opening, and a half overlay splits the frame between two doors. Each layout needs a different clearance at the hinge side and between paired doors. The hinge manufacturer gives the clearance figure for the hinge you plan to use. 

Subtract the clearances from the opening figures to get the finished door size. A single door that covers the opening needs a small gap at the hinge edge and a small gap at the latch edge. Paired doors need an even gap where they meet in the middle. Mark the final size on the plywood with a square and a sharp pencil before cutting. 

## Choose the plywood and plan the panel 

Plywood door panels work when the sheet is flat, dry and free of voids near the cuts. A thicker panel holds its shape better over a wide door, while a thin panel needs support. Check each sheet for warp by sighting along the edge before you buy it. Store the sheet flat until the day you cut it. 

Face grain and core quality change how the finished door looks. A sanded hardwood-faced sheet takes paint and stain evenly, and a sheet with a solid core cuts cleaner at the edges. Lower grades can work for a painted utility door in a workshop. Keep the best face outward and mark the back of each piece. 

Plan the cuts so the grain runs the way you want on the finished door. A vertical grain on tall doors reads as a panel, and a horizontal grain suits a wide low door. Lay out every piece on the sheet before cutting so you do not run short. Allow for the frame or stiffener when you work out the panel size. 

## Cut the panel square and clean 

A square panel starts with a straight reference edge on the sheet. Cut that edge first with a circular saw guided by a straightedge, then measure everything from it. Support the sheet on both sides of the cut so it does not sag and pinch the blade. A sharp, fine-tooth blade reduces tear-out on the veneer face. 

Score the face veneer with a knife along the cut line before sawing to limit splintering. Run the saw at a steady speed and keep the base flat on the sheet. Cut slightly oversize, then trim to the final line on a table saw or with a router and straightedge. The trimmed edge gives you a door with parallel sides and true corners. 

Check the panel for square by measuring both diagonals and comparing them. Equal diagonals mean the corners are square, which matters when the door goes into a tight opening. Label each panel with its cabinet position so panels do not get swapped later. A stack of identical panels saves time when you cut the next door. 

## Build a frame to keep the door flat 

A door frame stiffens a plywood panel and gives the hinge a solid place to bite. Build the frame from straight strips of solid wood or plywood and glue it to the back of the panel. A flat frame around the perimeter works for most garage cabinet doors. A wide door also needs a cross rail or a middle stile to stop the panel from bowing. 

Cut the frame pieces to fit inside the door outline and dry-fit them before gluing. Spread glue evenly, clamp the frame flat against the panel, and check the door for twist while the glue sets. Small brads or screws hold the frame in place while the clamps do their work. Wipe the squeeze-out at once so it does not harden on the face. 

An alternative is a flat panel with a glued and screwed stiffener, which suits a simple workshop door. A framed door looks more like a cabinet door and hides the panel edges behind the frame. Both approaches keep the plywood door panels from cupping over time. Choose one method and use it on every door so the run matches. 

## Fit hinges to the door and cabinet 

Hinges carry the weight of the door, so the type must match the door thickness and the overlay you chose. Concealed cup hinges need a bored hole in the door back and a mounting plate on the cabinet. Surface-mounted hinges screw to the face and the door edge and suit a simple build. Test one hinge on a scrap piece before drilling the real door. 

Mark hinge positions at the same height on every door so the run lines up. Keep the hinge clear of the frame joints, where the screw has little material to hold. Drill pilot holes for every screw to stop the plywood from splitting at the edge. Set the hinge adjustment to its middle range before you hang the door. 

Hang the door with one screw in each hinge first, then check the gap and swing. Adjust the hinge plates until the door sits level and closes without rubbing. Add the remaining screws once the door hangs correctly. A door that binds at the top or bottom needs a hinge adjustment, not a shorter door. 

## Finish the edges and the faces 

Edge finishing protects the exposed plywood core and makes the door look finished. Sand the cut edges smooth, then seal them with a coat of primer or a thin glue size. Plywood edges soak up finish faster than the face, so seal them before the topcoat. A glued hardwood edge band gives a durable edge on a door that gets handled a lot. 

Fill any voids or gaps at the edge with a sandable filler and sand it flush when dry. Sand the faces lightly with the grain and remove the dust before the first coat. Seal both faces of the door, including the back, so moisture enters and leaves evenly. A door sealed on one side only can cup as the seasons change. 

Apply the finish in thin coats and let each one dry fully before sanding lightly. Pay attention to the bottom edge of the door, where moisture from a wet floor collects. A sealed edge and a sealed face keep the door stable in a garage that sees damp air. Let the finish cure before you hang the door, so the hinge screws seat in solid material. 

## Hang, adjust and check the run 

Hanging the first door sets the pattern for every door after it. Fit the door, check the gap at the top, bottom and sides, and adjust the hinges until the gap is even. Open and close the door through its full swing to be sure nothing rubs. Mark the hinge position on the cabinet so the next door matches. 

Check that the door clears the cabinet contents when it opens. A door that swings into a wall or a parked tool needs a restrictor or a different hinge. Add a catch or a latch so the door stays shut when the cabinet is moved or bumped. A lockable catch suits a cabinet that holds detailing supplies and tools. 

Repeat the measuring, cutting and hanging steps for the remaining doors and compare each one to the first. Small differences in the opening show up once the doors are side by side. Adjust the hinges rather than trimming a finished door. A consistent gap across the run makes the whole cabinet look built rather than assembled. 

## Plywood Cabinet Door Questions 

### How thick should plywood be for garage cabinet doors? 

Plywood for garage cabinet doors is chosen by the door width and the hinge type. A thicker panel resists bowing over a wide door, while a thin panel needs a frame or stiffener behind it. The hinge you plan to use states the door thickness range it accepts, so pick the panel to suit that range. 

### Can I make cabinet doors from a single sheet of plywood? 

Yes, a single sheet of plywood can make several cabinet doors when you plan the cuts. Lay out every panel on the sheet before cutting so the grain direction stays consistent across the run. A single panel door works well when the door is narrow, and a wider door gains stiffness from a glued frame. 

### Do plywood doors need a frame? 

Plywood doors need a frame or a stiffener when the panel is wide or thin, because flat plywood can bow over time. The frame also gives hinges and catches solid material to screw into. A narrow door on a small cabinet can work as a plain panel with sealed edges. 

### What is the best way to finish plywood door edges? 

Plywood door edges are sealed before the face is finished, because the exposed core absorbs finish quickly. Sand the edge smooth, fill any voids, then apply primer or a thin sealer and sand lightly. A glued hardwood edge band adds durability where the door is handled often. 

### How do I stop plywood cabinet doors from warping? 

Plywood cabinet doors warp when one face takes on moisture differently from the other or when the panel is unsupported. Seal both faces and all edges, store the sheets flat before cutting, and add a frame to wide doors. Keep the finished cabinet away from standing water on the garage floor. 

### Which hinges work on plywood cabinet doors? 

Hinges for plywood cabinet doors depend on the door thickness and how much of the cabinet face the door covers. Concealed cup hinges need a bored hole and a mounting plate, while surface-mounted hinges screw to the face and edge. Match the hinge clearance to your overlay before you cut the door to size.
