How to Hang Pegboard on a Concrete Wall

Learn how to mount pegboard on concrete or block walls with masonry anchors, a hammer drill, spacers or furring strips, plus safety checks before drilling.

8 min read2 viewsHow to Hang Pegboard on a Concrete Wall
— · 0 votes
Contents
  1. Two ways to mount pegboard on concrete
  2. Tools and materials for the job
  3. Check the concrete wall before drilling
  4. Choosing masonry anchors for pegboard
  5. Marking and drilling the holes
  6. Mounting the pegboard with spacers or strips
  7. Planning the layout and load of the board
  8. Questions about pegboard on concrete walls
  9. Do you need a hammer drill to hang pegboard on concrete?
  10. Can you hang pegboard on concrete without drilling?
  11. Do I need spacers behind pegboard on a concrete wall?
  12. Can you use wedge anchors to hang pegboard?
  13. What size drill bit do I use for concrete anchors?

To hang pegboard on a concrete wall, fasten it to masonry anchors set in drilled holes. Spacers or wood furring strips hold the board off the wall so hooks can seat in the holes. A hammer drill with a concrete bit makes the holes, and the anchor package sets the bit size.

  • Check the wall for hidden pipes, wires and damp before you drill any hole.
  • Use a hammer drill and a carbide-tipped concrete bit sized to your anchors.
  • Leave a gap behind the board with spacers or furring strips so hooks fit.
  • Match the anchor to the wall: solid poured concrete and hollow block need different hardware.
  • Clear dust from every hole before setting an anchor so it grips the concrete.

Two ways to mount pegboard on concrete

Pegboard on concrete goes up in one of two ways: direct anchoring or furring strips. Direct anchoring means screws pass through the pegboard and spacers into anchors in the wall. Furring strips are wood or metal battens fixed to the concrete first, with the board screwed onto them.

Direct anchoring with pegboard spacers uses fewer materials and suits a single board on flat concrete. Each fastening point needs its own hole in the wall, so layout must be accurate. Uneven concrete can twist the board, because spacers only touch the wall at small points.

Furring strips suit wide runs of pegboard, uneven walls and walls that may stay slightly damp. The strips create a continuous air gap and give you wood to screw into anywhere along them. Several boards can then share the same frame, and you can move or replace boards without new drilling.

Tools and materials for the job

The core tool for hanging pegboard on concrete is a hammer drill fitted with a concrete drill bit. A hammer drill adds a rapid pounding action to the rotation, which breaks up concrete as it cuts. Concrete bits have a carbide tip that survives this impact where a wood or metal bit would dull.

Masonry anchors are the hardware that lets a screw grip inside a hole in concrete or block. Buy anchors, screws and the matching bit as one set, so every part fits the same hole size. Pegboard spacers or furring strips come next, along with washers to spread the load on the board.

Safety gear belongs on the list before any drilling into concrete starts. Drilling concrete throws grit and fine dust that can contain silica, which is harmful to breathe. Wear safety glasses, hearing protection and a dust mask rated for fine particles.

  • Hammer drill
  • Carbide-tipped concrete drill bit sized to the anchors
  • Masonry anchors and matching screws
  • Pegboard spacers or wood furring strips
  • Washers, level, tape measure and pencil
  • Shop vacuum or blow-out bulb for hole dust
  • Safety glasses, hearing protection and dust mask

Check the concrete wall before drilling

A concrete wall must be checked for buried pipes, wires and heating lines before you drill. Electrical conduit and plumbing sometimes run inside or along concrete, and a bit can damage them. Some concrete structures also contain tensioned steel cables, which are dangerous to cut. If you are unsure what is inside the wall, hire a trained specialist to scan it first.

Moisture is the second check, since hardboard pegboard swells and sags when it stays damp. Basement and exterior concrete walls can carry dampness through to the surface. Tape a square of plastic sheet to the wall and look for droplets under it later. On a damp wall, use metal or plastic pegboard and keep a clear air gap behind it.

The wall material decides which anchor will hold, so identify it before buying hardware. Poured concrete is solid through its thickness and accepts the full range of masonry anchors. Concrete block, also called cinder block, has hollow cores behind a thin outer shell. A drill bit that suddenly plunges forward has broken through into a hollow core.

Choosing masonry anchors for pegboard

Masonry anchors for pegboard should match the wall type and the weight the board will carry. Plastic sleeve anchors expand as a screw drives in, which suits light boards holding brushes or towels. Concrete screws cut their own thread into a pre-drilled hole and need no separate sleeve.

Wedge anchors are heavy-duty steel bolts that lock into solid concrete when you tighten the nut. The threaded end stays exposed, which suits furring strips or steel rails better than bare pegboard. Wedge anchors are made for solid concrete and should not go into hollow block.

Anchor spacing depends on board size, expected load and the rating printed on the anchor package. Place fasteners near each corner, along the edges and through the middle of the board. A middle row of fasteners stops the board from bowing when hooks pull outward.

Anchor typeWall typeLoadNotes
Plastic sleeve anchorPoured concrete or blockLightSimple to fit, screw size must match the sleeve
Concrete screwPoured concrete or blockLight to mediumNo sleeve, drill the exact hole size listed
Metal sleeve anchorPoured concrete or blockMedium to heavyExpands along its length when tightened
Wedge anchorSolid poured concrete onlyHeavyExposed bolt, suits furring strips or rails

Marking and drilling the holes

Marking pegboard holes on concrete starts with holding the board level against the wall. Choose pegboard holes at the fastening points and mark the concrete through them with a pencil. On a furring strip install, mark and drill the strip positions instead of the board.

Drill into concrete with the hammer function on and the bit held square to the wall. Start slowly to keep the tip from wandering, then raise the speed once the hole forms. Set the depth stop or a tape flag a little deeper than the anchor length. Let the drill do the work, pulling the bit out from time to time to clear grit.

Dust left inside a drilled hole weakens the grip of any masonry anchor. Clear each hole with a shop vacuum, a blow-out bulb or a small wire brush. If the bit hits rebar, the steel reinforcing bar inside concrete, stop and move the hole.

Mounting the pegboard with spacers or strips

Pegboard spacers hold the board away from the concrete so hook ends can pass through the holes. Without that gap, pegboard hooks hit the wall and cannot lock into place. Spacers come as plastic or metal sleeves, and a stack of washers can serve the same purpose. The needed depth depends on the hooks you plan to use.

Direct mounting starts by setting all masonry anchors flush with the concrete surface. Hold the board in place, slip a spacer behind each fastening hole and drive the screws. A washer under each screw head keeps it from pulling through the soft board. Tighten until snug, since overtightening can crack hardboard or crush the spacer.

Furring strip mounting fixes wood strips to the concrete first, then attaches the pegboard to the wood. Run strips around the board perimeter and add one across the middle for support. Use rot-resistant treated lumber or a moisture barrier where wood touches concrete. Check the strips with a level before screwing the board on with wood screws and washers.

Planning the layout and load of the board

A pegboard layout works when tools sit where the work happens and each item has a fixed spot. In a detailing bay, that might mean brushes, pads and spray bottles near the wash area. Lay the tools on the floor in the planned pattern before hanging any hooks.

Pegboard weight limits depend on the board material, its thickness, the hooks and the anchors behind it. Hang heavy items such as machine polishers low and close to the fastening points. Very heavy gear belongs on a dedicated shelf or bracket anchored straight into the concrete.

Hook locks or clips keep pegboard hooks from lifting out when you grab a tool. Outlining each tool with a marker shows at a glance what is missing after a job. Inspect the fasteners periodically and retighten any screw that has worked loose.

Questions about pegboard on concrete walls

Do you need a hammer drill to hang pegboard on concrete?

Yes, a hammer drill is the right tool for drilling concrete for pegboard anchors. A regular drill with a masonry bit can cut soft block slowly, but poured concrete resists it. Rotary hammers also work and handle larger holes for heavy anchors.

Can you hang pegboard on concrete without drilling?

Not reliably, because adhesive alone is a weak hold for pegboard on concrete that carries tools. Construction adhesive and mounting strips can let go on dusty, damp or uneven concrete. Hooks also pull outward on the board, which stresses a glued bond. Masonry anchors set in drilled holes give a much more dependable hold for loaded boards.

Do I need spacers behind pegboard on a concrete wall?

Yes, pegboard on concrete needs spacers or furring strips so hooks have room behind the board. Flush against the wall, the holes are blocked and hooks cannot seat. The gap also lets air move, which helps keep a hardboard panel dry.

Can you use wedge anchors to hang pegboard?

Yes, wedge anchors can hold pegboard, but they fit furring strips or rails better than the bare board. The exposed bolt end sits proud of the surface and can block nearby hooks. Wedge anchors also require solid poured concrete, not hollow block.

What size drill bit do I use for concrete anchors?

The correct concrete drill bit size is the one printed on the masonry anchor package. An oversized hole lets the anchor spin, while an undersized one can split or jam it. Drill a little deeper than the anchor length to leave room for dust.

Read next

Latest articles