How to Clean a Pressure Washer Water Tank
A step-by-step routine to drain, rinse, sanitize and refill a pressure washer water tank, plus how to keep the intake screen and water supply clean.
Contents
- Start with a full drain and rinse
- Scrub the walls and floor
- Sanitize the tank for fresh water
- Clean the water intake screen
- Dry, refill and store the tank
- Set a cleaning routine you can keep
- Avoid these cleaning mistakes
- Pressure Washer Water Tank Questions
- How often should I clean a pressure washer water tank?
- Can I use bleach to sanitize the water tank?
- Why does my pressure washer water supply keep cutting out?
- What causes algae in a pressure washer water tank?
- Should the tank be full or empty for storage?
- Can I clean the inside of the tank with the pressure washer?
Cleaning a pressure washer water tank means draining it, flushing out algae and debris, scrubbing the walls, sanitizing the tank, and rinsing it before you refill. The job also covers the water intake screen, because a blocked screen starves the pump even when the tank itself looks clean. A steady cleaning routine keeps the water supply fresh and protects the pump from grit.
- Drain and rinse the tank before you scrub, so loose debris leaves with the first flush.
- Sanitize the tank with a product made for drinking water or potable water systems and follow its label.
- Clean the water intake screen at the same time, since a clogged screen limits the pressure washer water supply.
- Let the tank dry fully with the lid off before you refill it, which slows algae growth.
- Store the tank empty and covered between jobs to keep dust and light out.
Start with a full drain and rinse
A tank drain and rinse is the first step of pressure washer water tank cleaning, because it removes the loose material before you touch the walls. Park the tank on level ground and open the drain valve or remove the drain plug. Let the old water run out completely, then close the valve. Tilt the tank slightly toward the drain if the outlet sits at one corner.
Refill the tank partway with clean water and swish it around the walls and floor. Open the drain again and let the rinse water carry out the silt. Repeat the fill and drain until the water leaving the tank runs clear. This flush loosens the soft layer of algae and debris that collects on the bottom.
Collect the dirty water instead of letting it run across a driveway or into a drain. A bucket under the outlet catches the first heavy flush. The rinse water can go to a lawn or a drain that accepts wash water in your area. Check local rules on where wash water may go before you start.
Scrub the walls and floor
Scrubbing removes the film of algae and debris that a rinse alone leaves on the tank walls. Use a soft brush with a long handle so you can reach the bottom without leaning into the tank. A non-abrasive pad works on flat walls and corners. Avoid metal scrapers that scratch the plastic or liner.
Work from the top down and pay attention to the corners, seams and the area around the outlet. Algae and debris gather where water sits still and where light reaches the walls. A mix of mild dish soap and warm water lifts the film without harsh fumes. Rinse the brush between passes so you do not spread the dirt back onto clean plastic.
Drain the soapy water and rinse the tank again until no suds remain. Suds left behind can foam in the pump and reach the spray. Wipe the walls with a clean cloth if the tank is small enough to reach. Let the tank air out before the sanitizing step.
Sanitize the tank for fresh water
Tank sanitizing kills the algae and bacteria that a scrub leaves in scratches and pores. Use a sanitizer labeled for drinking water tanks or potable water systems, and follow the label for the mix and contact time. Never mix a chlorine product with an acid or ammonia cleaner, since the fumes can harm you. Wear gloves and eye protection while you work.
Fill the tank with the sanitizing solution so it reaches every wall, then let it sit for the contact time on the label. Run some of the solution through the outlet and the hose that feeds the pump. That step treats the parts the water passes through on its way to the pressure washer. Drain the solution when the contact time ends.
Rinse the tank with clean water until the smell of sanitizer is gone. A faint chlorine smell can linger in plastic, so rinse once more if you plan to use the water on a surface that matters. Let the tank dry with the lid open and the outlet clear. Store sanitizer out of reach of children and pets.
Clean the water intake screen
The water intake screen protects the pump, and a clogged screen weakens the pressure washer water supply. Find the screen where the hose connects to the tank outlet or at the pump inlet, depending on your setup. Pull the screen out and hold it up to the light. Silt, algae strands and grit show up as dark patches on the mesh.
Rinse the screen from the back so debris pushes out the way it came in. A soft brush removes the film that water alone leaves behind. If the mesh is torn or stretched, replace the screen, because a damaged screen lets grit reach the pump. Never run the pressure washer without the screen in place.
Check the hose and fittings for grit while the screen is out. A cracked or loose fitting lets air into the line and makes the pump surge. Reassemble the parts and run clean water through the line before you connect the spray gun. A clear intake path is part of every water tank cleaning routine.
Dry, refill and store the tank
Drying the tank between jobs slows algae growth and keeps the water supply fresher. Leave the lid off and the drain open in a shaded spot until the inside is dry to the touch. Sunlight helps drying but also feeds algae in a clear tank, so shade is the safer choice. Wipe up standing water in the corners with a clean cloth.
Refill the tank with clean water just before a job rather than storing it full for long periods. Water that sits in a warm tank gives algae a place to grow. If you must keep water in the tank, keep it covered and out of direct light. Add a tank treatment made for stored water only if its label allows that use.
Store the empty tank with the lid on and the drain closed to keep dust and insects out. Keep the tank off bare soil and away from chemicals such as fertilizer or oil. A clean, dry tank is ready for the next fill. Note the date of the last cleaning on a checklist so the routine stays on schedule.
Set a cleaning routine you can keep
A water tank cleaning routine works when it fits the way you use the pressure washer. Tanks that sit in sunlight or hold water between jobs need attention sooner than tanks drained after each use. Decide the trigger first, such as a visible film, a smell, or a set number of fills. Write the trigger on your equipment checklist.
The routine covers four steps in order: drain and rinse, scrub, sanitize, and dry. Add the intake screen to the same list so it is never skipped. Keep the brush, gloves, sanitizer and a spare screen together in one box. A ready kit cuts the time the job takes and makes the next clean easier.
Record each cleaning and the condition of the tank and screen. Notes about algae growth or grit tell you when to shorten the interval. A simple log on a clipboard or a note on the tank lid is enough. Review the log when you plan maintenance for the rest of the equipment.
Avoid these cleaning mistakes
Harsh chemicals damage tanks and pumps, so keep them out of the water path. Solvents, bleach at full strength and abrasive powders can etch plastic and leave residue that reaches the spray. Use only cleaners labeled for the tank material and for water systems. When a label is unclear, choose another product.
A pressure washer should never clean the inside of its own water tank. The high-pressure jet can crack plastic, drive grit into seams and splash back at you. Wash the tank by hand with a brush and a gentle flow from a hose. Save the pressure washer for the outside of the equipment.
Skipping the screen or the final rinse undoes the work of the whole clean. Grit left in the line reaches the pump, and sanitizer left in the tank can harm plants or surfaces. Check both before the tank goes back into service. If a tank is cracked, has a broken fitting or smells of chemicals after rinsing, replace it or have it inspected by a specialist.
Pressure Washer Water Tank Questions
How often should I clean a pressure washer water tank?
The right interval depends on how you use the tank, how much light reaches it and whether water sits inside between jobs. A tank that holds water in a warm, bright spot needs cleaning sooner than one drained and dried after each use. Check the walls and the intake screen before every fill, and clean when you see a film, a smell or grit.
Can I use bleach to sanitize the water tank?
Bleach can sanitize a water tank only when a product label gives a mix for potable water systems and you follow it exactly. Household bleach at full strength can damage plastic and leave residue that reaches the pump and the spray. Never mix bleach with an acid or ammonia cleaner, because the fumes can harm you. Choose a sanitizer labeled for the tank instead.
Why does my pressure washer water supply keep cutting out?
A weak or pulsing water supply points to a blocked intake screen, a loose fitting or a tank outlet that is not fully open. Silt and algae strands on the screen starve the pump and make it surge or lose pressure. Clean the screen, check the hose for kinks and confirm the outlet valve is open. Air leaking into a fitting causes the same symptom.
What causes algae in a pressure washer water tank?
Algae grows in a pressure washer water tank when water sits still, the tank is clear or open to light, and the inside stays warm. Leftover film on the walls feeds the growth, and a partly full tank gives it a place to spread. Draining and drying the tank between jobs and storing it covered and shaded slows the problem.
Should the tank be full or empty for storage?
An empty, dry tank is the safer choice for storage between jobs. Water left inside a warm tank gives algae a place to grow, and a full tank is heavy to move. Store the tank with the lid on and the drain closed after it dries. Fill it with clean water just before you use the pressure washer.
Can I clean the inside of the tank with the pressure washer?
No, you should not clean the inside of a water tank with the pressure washer itself. The high-pressure jet can crack plastic walls, push grit into seams and splash back at you. Wash the inside by hand with a soft brush and a gentle flow from a hose. A professional can inspect a tank that is cracked or badly stained.