Find Your Vehicle's Designated Jacking Points: A Practical Workflow for Safe Lifting

Find the correct front and rear car jacking points, verify them before lifting, and build a repeatable routine with the right tools, equipment care and a pre-job checklist.

10 min readVehicle Lifting & Wheel Removal Safety8 viewsFind Your Vehicle's Designated Jacking Points: A Practical Workflow for Safe Lifting
— · 0 votes
Contents
  1. What Are Vehicle Jacking Points?
  2. How to Find the Jacking Point on a Car
  3. Using the Vehicle Owner's Manual
  4. Recognising the Vehicle Jacking Point Sign
  5. Car Jacking Points Front vs Rear
  6. Car Jacking Points Front
  7. Car Jacking Points Rear
  8. Car Jacking Points of Proof: Verifying Before You Lift
  9. Tools and Supplies for Safe Lifting
  10. The Lifting Sequence Within a Detailing Workflow
  11. Common Mistakes and How to Avoid Them
  12. Equipment Care and Storage
  13. Checklist Before the Next Job
  14. Building a Vehicle Notes Routine

To find your vehicle's designated jacking points, check the jacking diagram in the vehicle owner's manual first, then match it to the markings on the car itself. These markings are usually small arrows, triangles, notches or cut-outs along the rocker panel sill or pinch weld behind the front wheels and ahead of the rear wheels. Before any weight goes on the jack, confirm the point by looking at the metal. The manufacturer designed vehicle jacking points as reinforced areas that can carry the car's load without bending panels, crushing pipes or cracking components. Lifting anywhere else risks damage to the car and injury to you.

For detailers who remove wheels to clean barrels, arches and calipers, finding jacking points should become a fixed step in the workflow. It should not be a guess made at the start of every job. The sections below set out the sequence, the tools, the checks and a reusable checklist.

What Are Vehicle Jacking Points?

Vehicle jacking points are the reinforced locations on a car's body or chassis that the manufacturer has approved for lifting. Manuals may call them designated lifting points. On most modern unibody cars they sit on the pinch weld seam under each side sill. Some vehicles also have central points on the front subframe or rear crossmember for a floor jack. Body-on-frame trucks and SUVs are often lifted at the frame rails or axles, as the manual specifies.

Manuals often separate two kinds of point:

  • Jacking points are where the jack head contacts the vehicle to raise it.
  • Support points are where jack stands hold the vehicle once it is raised. These are sometimes the same locations and sometimes separate ones nearby.

Knowing which is which keeps you from using the jack's only good location and leaving nowhere safe for the stand.

How to Find the Jacking Point on a Car

The reliable way to find the jacking point on a car is to combine three sources: the owner's manual diagram, the markings on the car, and a visual check of the metal. Use them in this order.

  1. Open the vehicle owner's manual. Look in the index under jacking, lifting, flat tyre or wheel changing. The diagram shows each point and often says which jack to use: the supplied scissor jack, a garage floor jack or a two-post lift.
  2. Locate the matching mark on the vehicle. Kneel at the sill behind the front wheel and ahead of the rear wheel and look for the vehicle jacking point sign described below.
  3. Inspect the area. Clean off dirt so you can see the metal. Check for rust, previous crush damage, or plastic trim that must be removed or avoided.
  4. Confirm the jack fits. Make sure your jack saddle or adapter sits flat on the point without touching side skirts or body panels.
  5. Record it. Note the locations for that make and model so the next job on a similar car starts faster.

Using the Vehicle Owner's Manual

The manual is the authority for every vehicle because jacking point layouts differ between manufacturers, models and even trim levels. If the physical manual is missing, many manufacturers publish digital versions for owners. Do not assume a car shares points with another model from the same brand.

Recognising the Vehicle Jacking Point Sign

A vehicle jacking point sign is a small marking that shows exactly where the jack should go. Common jacking-point symbols include:

  • a triangle or arrow pressed into or printed on the side sill, pointing at the lift location
  • two notches or cut-outs in the pinch weld, with the jacking area between them
  • a reinforced pad, a rubber block, or a removable plastic cap in the sill trim
  • a flattened or thicker section of the pinch weld seam

If the markings are worn, painted over or hidden by aftermarket skirts, rely on the manual diagram and do not guess.

Car Jacking Points Front vs Rear

Front and rear jacking points work the same way, but their locations and the risks around them differ. The table summarises typical patterns. Your manual decides the actual points for your vehicle.

AspectFront jacking pointsRear jacking points
Typical side locationPinch weld or sill just behind the front wheel archPinch weld or sill just ahead of the rear wheel arch
Possible central locationFront subframe or crossmember, if the manual approves itRear crossmember, subframe, or axle housing on some vehicles, if approved
Components to avoidOil pan, transmission pan, steering parts, plastic undertrays, radiator supportsFuel tank, exhaust pipes, spare wheel well, fuel and brake lines, suspension arms not listed as points
Common detailing reasonRemoving front wheels to clean calipers and inner archesRemoving rear wheels for barrel cleaning and arch dressing

Car Jacking Points Front

Car jacking points at the front are usually on the side sills near the front wheels, with a possible central point on the front subframe. The engine sits at the front, so these points often carry the heaviest load. Many oil pans, transmission pans and plastic aero trays hang low near the front centre and can look like solid lifting surfaces. They are not. Only use a central front point if the manual names it.

Car Jacking Points Rear

Car jacking points at the rear are typically on the side sills ahead of the rear wheels, and some vehicles add a central crossmember or axle point. Exhaust pipes, the fuel tank and the spare wheel well all sit in this area. Some vehicles allow lifting under a solid rear axle or differential, but many do not. Check the manual instead of following a habit from a different car.

Car Jacking Points of Proof: Verifying Before You Lift

Treat jacking as a point you must prove before you load it, not one you assume. Think of your car jacking points of proof as three confirmations that should all agree:

  1. The document. The manual diagram shows this location.
  2. The marking. A jacking-point symbol, notch or pad on the car matches the diagram.
  3. The metal. The surface is solid, free of heavy rust or old crush damage, and is not plastic trim.

If any one of the three is missing or doubtful, stop and resolve it before lifting. Then raise the car only slightly, until the tyre just begins to unload. Watch for flexing, creaking or the saddle shifting. Continue only if the contact stays stable.

Tools and Supplies for Safe Lifting

A safe lifting kit needs a properly rated jack, matching jack stands, wheel chocks and something to protect the jacking point. Keep these items together in a dedicated tub or drawer:

  • Floor jack or trolley jack rated above the load it will lift. Check its rating against the vehicle weight shown on the door-jamb plate or in the manual.
  • Jack stands in a matched pair, rated for the vehicle. Never work under or beside a car held only by a jack.
  • Wheel chocks for the wheels that stay on the ground.
  • Pinch weld adapter or slotted rubber jack pad, so the seam is not flattened and the paint is protected.
  • Lug wrench or breaker bar and correct sockets, including a lock-nut key if one is fitted.
  • Torque wrench to refit wheels to the manufacturer's specification.
  • Torch or headlamp to read markings under the sill.
  • Kneeling pad and a stiff brush or cloth to clear dirt from the jacking area before inspection.
  • Vehicle notes sheet or log to record jacking point locations for repeat clients.

The Lifting Sequence Within a Detailing Workflow

Lifting should happen at a fixed point in the detail, after the car is parked and secured and before any wheel cleaning begins. A consistent order stops you from skipping a safety step when you are busy.

  1. Park on firm, level ground. Avoid soft gravel, slopes and wet sloping wash bays. Put the car in park, or in gear for a manual, and set the parking brake.
  2. Chock the wheels. Chock the wheels on the opposite axle from the one you are lifting.
  3. Loosen the wheel nuts slightly while the tyre is on the ground. The tyre's grip stops the wheel from spinning.
  4. Locate and verify the jacking point. Use the three confirmations above.
  5. Position the jack with its adapter and raise it until it just contacts the point. Check alignment once more.
  6. Lift steadily until the tyre clears the ground by enough to remove the wheel.
  7. Place the jack stand at the approved support point and lower the car gently onto it. Leave the jack lightly in place as a backup where space allows.
  8. Remove the wheel and lay it flat, face up, on a soft mat away from the walkway.
  9. Detail the wheel and arch.
  10. Refit the wheel, raise the car off the stand, remove the stand, and lower it. Then torque the nuts to specification in a star pattern.

Work one corner or one axle at a time unless you have enough stands and approved points to support more safely. That keeps the routine simple.

Common Mistakes and How to Avoid Them

Most jacking damage comes from guessing the location, using the wrong contact surface, or skipping the jack stand.

  • Lifting on plastic side skirts or undertrays. They crack and can shift suddenly. Find the metal point behind or beneath the trim.
  • Crushing the pinch weld with a bare jack saddle. The seam bends and the exposed metal can rust later. Always use a slotted pad or adapter.
  • Jacking under the oil pan, exhaust, or fuel tank. These parts are not designed to carry load. Confirm central points in the manual.
  • Relying on memory from another car. Layouts vary. Check the manual or your notes for each make and model.
  • Using the jack as the only support. Hydraulic jacks can lose pressure. Always transfer the load to rated jack stands.
  • Lifting on an uneven or soft surface. The jack and stands can sink or tilt. Use a level, hard floor.
  • Ignoring rust or previous damage. A weakened point can fold under load. If a point looks compromised, do not use it, and tell the vehicle owner.

Equipment Care and Storage

Clean, inspect and store lifting equipment after every job so it is reliable at the start of the next one.

  • Wipe down the jack and stands to remove water, wheel cleaner and road grime. Chemicals from detailing can corrode metal and degrade seals.
  • Inspect the jack for hydraulic fluid leaks, a saddle that will not hold height, bent arms or damaged wheels.
  • Inspect the jack stands for bent legs, cracked welds, and worn ratchet teeth or locking pins.
  • Check rubber pads and adapters for splits or embedded grit that could scratch paint. Replace any that are worn.
  • Store the jack fully lowered and the stands at their lowest setting. Keep them dry and off the wash-bay floor.
  • Keep the kit together in one labelled location so nothing is missing when a car arrives.
  • Follow the jack manufacturer's maintenance instructions for fluid checks and servicing intervals.

Checklist Before the Next Job

A short pre-job checklist turns jacking into a repeatable routine. Run through it before each vehicle that needs wheels removed.

  • Vehicle make, model and year noted, and manual or saved notes available
  • Front jacking points and rear jacking points located and marked on your notes sheet
  • Jack and stands rated for the vehicle, clean and inspected
  • Pinch weld adapter or rubber pad present and in good condition
  • Wheel chocks, lug wrench, sockets, lock-nut key and torque wrench ready
  • Wheel torque specification for the vehicle at hand
  • Firm, level working area clear of hoses, buckets and trip hazards
  • Torch or headlamp charged
  • Soft mat ready for removed wheels
  • Any pre-existing damage to sills or jacking points photographed and noted

Building a Vehicle Notes Routine

Keeping a simple record of each vehicle's jacking points is the most effective way to save time on repeat work. For each car, note the make, model and year. Record where the side points are, whether a central front or rear point is approved, which adapter fits, the wheel nut torque, and any trim or damage to watch for. Over time this becomes a reference library. It speeds up preparation while keeping verification in place, because you still confirm the marking and the metal on the car in front of you before lifting.

Related articles